當前位置:首頁 > 工業控制 > 電子設計自動化

Microsemi 公司的SmartFusion雙馬達控制套件包括SmartFusion 評估板和與之配對的TRINAMIC公司的TMCM-AC-840子板,能為步進馬達和無刷DC馬達(BLDC)提供定制化片上系統(cSoC)馬達控制平臺,而SmartFusion cSoC器件集成了FPGA,ARM® Cortex™-M3處理器,以及可編程的模擬,提供完全定制的IP保護和容易使用;此外還集成了SRAM存儲器和SPI閃存.本文介紹了SmartFusion cSoC主要特性,方框圖和系統架構圖,BLDC和步進馬達演示設計基本框圖以及SmartFusion雙馬達控制套件主要特性,SmartFusion 評估板主要特性,以及TMCM-AC-840子板主要特性,電路圖和馬達控制子板PCB布局圖.

The SmartFusion® family of cSoCs builds on the technology first introduced with the Fusion mixed signal FPGAs. SmartFusion cSoCs are made possible by integrating FPGA technology with programmable high-performance analog and hardened ARM Cortex-M3 microcontroller blocks on a flash semiconductor process. The SmartFusion cSoC takes its name from the fact that these three discrete technologies are integrated on a single chip, enabling the lowest cost of ownership and smallest footprint solution to you.

SmartFusion定制片上系統(cSoC)主要特性:

Microcontroller Subsystem (MSS)

• Hard 100 MHz 32-Bit ARM® Cortex™-M3

– 1.25 DMIPS/MHz Throughput from Zero Wait State

Memory

– Memory Protection Unit (MPU)

– Single Cycle Multiplication, Hardware Divide

– JTAG Debug (4 wires), Serial Wire Debug (SWD, 2 wires), and Single Wire Viewer (SWV) Interfaces

• Internal Memory

– Embedded Nonvolatile Flash Memory (eNVM), 128 Kbytes to 512 Kbytes

– Embedded High-Speed SRAM (eSRAM), 16 Kbytes to 64 Kbytes, Implemented in 2 Physical Blocks to Enable Simultaneous Access from 2 Different

Masters

• Multi-Layer AHB Communications Matrix

– Provides up to 16 Gbps of On-Chip Memory Bandwidth,1 Allowing Multi-Master Schemes

• 10/100 Ethernet MAC with RMII Interface2

• Programmable External Memory Controller, Which

Supports:

– Asynchronous Memories

– NOR Flash, SRAM, PSRAM

– Synchronous SRAMs

• Two I2C Peripherals

• Two 16550 Compatible UARTs

• Two SPI Peripherals

• Two 32-Bit Timers

• 32-Bit Watchdog Timer

• 8-Channel DMA Controller to Offload the Cortex-M3 from Data Transactions

• Clock Sources

– 32 KHz to 20 MHz Main Oscillator

– Battery-Backed 32 KHz Low Power Oscillator with Real-Time Counter (RTC)

– 100 MHz Embedded RC Oscillator; 1% Accurate

– Embedded Analog PLL with 4 Output Phases (0, 90, 180, 270)

High-Performance FPGA

• Based on proven ProASIC®3 FPGA Fabric

• Low Power, Firm-Error Immune 130-nm, 7-Layer Metal, Flash-Based CMOS Process

• Nonvolatile, Live at Power-Up, Retains Program When Powered Off

• 350 MHz System Performance

• Embedded SRAMs and FIFOs

– Variable Aspect Ratio 4,608-Bit SRAM Blocks

– x1, x2, x4, x9, and x18 Organizations

– True Dual-Port SRAM (excluding x18)

– Programmable Embedded FIFO Control Logic

• Secure ISP with 128-Bit AES via JTAG

• FlashLock® to Secure FPGA Contents

• Five Clock Conditioning Circuits (CCCs) with up to 2 Integrated Analog PLLs

– Phase Shift, Multiply/Divide, and Delay Capabilities

– Frequency: Input 1.5–350 MHz, Output 0.75 to 350 MHz

Programmable Analog

Analog Front-End (AFE)

• Up to Three 12-Bit SAR ADCs

– 500 Ksps in 12-Bit Mode

– 550 Ksps in 10-Bit Mode

– 600 Ksps in 8-Bit Mode

• Internal 2.56 V Reference or Optional External Reference

• One First-Order ΣΔ DAC (sigma-delta) per ADC

– 8-Bit, 16-Bit, or 24-Bit 500 Ksps Update Rate

• Up to 5 High-Performance Analog Signal Conditioning Blocks (SCB) per Device, Each Including:

– Two High-Voltage Bipolar Voltage Monitors (with 4 input ranges from ±2.5 V to

–11.5/+14 V) with 1% Accuracy

– High Gain Current Monitor, Differential Gain = 50, up to 14 V Common Mode

– Temperature Monitor (Resolution = ¼°C in 12-Bit Mode; Accurate from –55°C to 150°C)

• Up to Ten High-Speed Voltage Comparators (tpd = 15 ns)

Analog Compute Engine (ACE)

• Offloads Cortex-M3–Based MSS from Analog Initialization and Processing of ADC, DAC, and SCBs

• Sample Sequence Engine for ADC and DAC Parameter Set-Up

• Post-Processing Engine for Functions such as Low-Pass Filtering and Linear Transformation

• Easily Configured via GUI in Libero® Integrated Design (IDE) Software

I/Os and Operating Voltage

• FPGA I/Os

– LVDS, PCI, PCI-X, up to 24 mA IOH/IOL

– Up to 350 MHz

• MSS I/Os

– Schmitt Trigger, up to 6 mA IOH, 8 mA IOL

Up to 180 MHz

• Single 3.3 V Power Supply with On-Chip 1.5 V Regulator

• External 1.5 V Is Allowed by Bypassing Regulator (digital VCC = 1.5 V for FPGA and MSS, analog VCC =3.3 V and 1.5 V)

SmartFusion系列產品:


圖1.SmartFusion cSoC 方框圖

圖2.SmartFusion cSoC 系統架構圖

SmartFusion雙馬達控制套件

Microsemi’s SmartFusion Dual Motor Control Kit features a SmartFusion evaluation board paired with TRINAMIC’s TMCM-AC-840 Daughter Board to provide a customizable system-on-chip (cSoC) motor control prototyping platform for stepper and brushless DC motors (BLDC). One of each type of motor is included along with necessary cables and power supplies. SmartFusion cSoCs are the only devices that integrate an FPGA, an ARM® Cortex™-M3 processor, and programmable analog, offering full customization, IP protection, and ease- of-use. The device contains on-chip flash and on-chip SRAM memory, as well as additional SPI flash memory on the board.

SmartFusion FPGA fit well to motion control applications. Due to the combination of hardware, software, and additional analog components complex systems can be integrated within a single chip. This drastically reduces the number of required components to realize a motion control unit. Real time critical tasks can be implemented in hardware. Complex - but less real time critical tasks - can be realized in software. Real Time critical tasks are commutation of fast rotating BLDC motors or processing of high resolution encoder signals. Processing of analog signals, e.g., voltage and current measurement is a typical task in motion control applications. Therefore, the SmartFusion’s. analog I/Os and processing functionality can be used.

SmartFusion 評估板主要特性:

• Supports SmartFusion evaluation,including ARM Cortex-M3, FPGA and programmable analog

• Free one-year Libero Integrated Design Environment (IDE) software and Gold license with SoftConsole for embedded design

• Two USB cables

• Online user’s guide, tutorial and design examples

• Printed circuit board (PCB) schematics, layout fi les and bill-of-materials (BOM)

• Board features

- Ethernet interface

- USB port for power and HyperTerminal

- USB port for programming and debug

- J-Link header for debug

- Mixed signal header

- SPI fl ash – off-chip memory

- Reset and 2 user switches, 8 LEDs

- POT for voltage / current monitor

- Temperature monitor

- Organic light-emitting diode (OLED)

Together with Trinamic’s integrated BLDC motor gate driver TMC603A (or with the integrated stepper motor driver TMC262), one can realize a power stage with a couple of components as demonstrated with the TMCM-AC-840 Daughter Board Kit for direct plug to the ACTEL SmartFusion. Evaluation Kit boards or Development Kit boards.

The TRINAMIC TMCM-AC-840 Daughter Board Kit is a power driver for brushless DC motors (BLDC) as well as stepper motors. The TMCM-AC-840 Daughter Board Kit incorporates one TMC603A BLDC motor driver IC and one TMC262 coolStep. stepper motor driver IC as well as two motors (one BLDC and one stepper motor) and a fitting portable power supply to start right away.

The TMCM-AC-840 is designed to operate with the ACTEL SmartFusion. Development Kit (Revision C and later) as well as the ACTEL SmartFusion. Evaluation Kit as both boards are pin-compatible regarding their Mixed Signal Expansion Header (see the ACTEL user guides for both boards). When using the TMCM-AC-840 in combination with an ACTEL SmartFusion. Development Kit that is equipped with the larger A2F500 SmartFusion. FPGA, some additional analog I/Os are available on the Mixed Signal Header. All signals of the Mixed Signal Expansion Header are easily accessible via pin headers on the TMCM-AC-840 daughter board.

TMCM-AC-840子板主要特性:

One BLDC motor pre-driver TMC603A

o Integrated dual range high precision current measurement amplifiers

o Supports shunt less current measurement using power MOS transistor RDSon

o hallFX™sensorless back EMF commutation emulates hall sensors

o Integrated break-before-make logic: No special microcontroller PWM hardware required

o See the TMC603A datasheet for more information [2]

? One stepper motor driver TMC262

o Energy saving high resolution microstepping two phase stepper driver with step and direction interface and external power stage

o High precision sensor-less motor load measurement stallGuard2™

o Energy efficiency and coolness by automatic load dependant motor current regulation technology coolStep™? Save up to 75% of energy!

o See the TMC262 datasheet for more information [3]

? One BLDC Motor (Qmot QBL4208-41-04-006)

o Maximum rated current 1.8A, peak current 5.4A, see motor spec/user guide for more information on electrical and mechanical parameters [6]

? One Stepper Motor (Qmot QSH4218-35-10-027)

o Maximum current 1.0A, see motor spec/user guide for more information on electrical and mechanical parameters [5]

? One portable power supply with international connectors, 24V/1A (version 1.3 and higher)

? Hard top case for easy handling and safe transport (version 1.3 and higher)

? The Board and the driver stages support maximum motor currents of up to 2A for stepper driver block and up to 4A (5A with good cooling) for the BLDC driver block.

? Easy plug and play solution using the freely available demo design (under BSD) for the BLDC and stepper functionality

? Hall-sensor interface for BLDC motors

? ABN encoder interface for high precision position measurement

o The encoder interface can be used with the stepper or with the BLDC motor.

? Various analog signals connected to the analog blocks (Signal Conditioning Blocks, SCBs) of the Actel SmartFusion™Device for, e.g., voltage measurement

? Additional RSENSE measurement pins

? All signals of the Mixed Signal Expansion Header can be accessed via additional pin headers for test and measurement

? Parallel operation of BLDC and stepper motor driver

? Pin-compatible to both the Actel SmartFusion™Development Kit as well as the Actel SmartFusion™Evaluation Kit

? Each driver requires a separate DC supply voltage

o The stepper driver block (TMC262): +VM262 = 12V to 40V

o The BLDC driver block (TMC603A): +VM603 = 12V to 48V

o Using jumpers, a single power supply can be used for both drivers

SmartFusion雙馬達控制套件包括:

For this demonstration design, the SmartFusion Dual Motor Control Kit comes with the following:

• SmartFusion Evaluation Kit board

• Trinamic TMCM-AC-840 daughter board kit (including 2 motors)

• 2 USB cables for programming and UART connection to your workstation

• Microsemi Libero® software tool chain

• FlashPro programming software

• 1 power supply unit

For each motor block (stepper or BLDC) you need a separate power supply unit

– With only one power supply you can only drive one motor at a time

圖3. BLDC和步進馬達演示設計基本框圖



圖4. SmartFusion雙馬達控制套件外形圖:

上:SmartFusion評估板;下:TMCM-AC-840馬達控制子板


圖5.TMCM-AC-840馬達控制子板電路圖(1)

圖6.TMCM-AC-840馬達控制子板電路圖(2)

圖7.TMCM-AC-840馬達控制子板電路圖(3)

圖8.TMCM-AC-840馬達控制子板電路圖(4)

圖9.TMCM-AC-840馬達控制子板電路圖(5)

圖10.TMCM-AC-840馬達控制子板電路圖(6)


圖11.TMCM-AC-840馬達控制子板PCB布局圖:頂層
詳情請見:
http://www.actel.com/documents/SmartFusion_DS.pdf

http://www.actel.com/documents/SmartFusion_DUAL_MOTOR_CONTROL_QS.pdf



本站聲明: 本文章由作者或相關機構授權發布,目的在于傳遞更多信息,并不代表本站贊同其觀點,本站亦不保證或承諾內容真實性等。需要轉載請聯系該專欄作者,如若文章內容侵犯您的權益,請及時聯系本站刪除。
換一批
延伸閱讀

9月2日消息,不造車的華為或?qū)⒋呱龈蟮莫毥谦F公司,隨著阿維塔和賽力斯的入局,華為引望愈發顯得引人矚目。

關鍵字: 阿維塔 塞力斯 華為

加利福尼亞州圣克拉拉縣2024年8月30日 /美通社/ -- 數字化轉型技術解決方案公司Trianz今天宣布,該公司與Amazon Web Services (AWS)簽訂了...

關鍵字: AWS AN BSP 數字化

倫敦2024年8月29日 /美通社/ -- 英國汽車技術公司SODA.Auto推出其旗艦產品SODA V,這是全球首款涵蓋汽車工程師從創意到認證的所有需求的工具,可用于創建軟件定義汽車。 SODA V工具的開發耗時1.5...

關鍵字: 汽車 人工智能 智能驅動 BSP

北京2024年8月28日 /美通社/ -- 越來越多用戶希望企業業務能7×24不間斷運行,同時企業卻面臨越來越多業務中斷的風險,如企業系統復雜性的增加,頻繁的功能更新和發布等。如何確保業務連續性,提升韌性,成...

關鍵字: 亞馬遜 解密 控制平面 BSP

8月30日消息,據媒體報道,騰訊和網易近期正在縮減他們對日本游戲市場的投資。

關鍵字: 騰訊 編碼器 CPU

8月28日消息,今天上午,2024中國國際大數據產業博覽會開幕式在貴陽舉行,華為董事、質量流程IT總裁陶景文發表了演講。

關鍵字: 華為 12nm EDA 半導體

8月28日消息,在2024中國國際大數據產業博覽會上,華為常務董事、華為云CEO張平安發表演講稱,數字世界的話語權最終是由生態的繁榮決定的。

關鍵字: 華為 12nm 手機 衛星通信

要點: 有效應對環境變化,經營業績穩中有升 落實提質增效舉措,毛利潤率延續升勢 戰略布局成效顯著,戰新業務引領增長 以科技創新為引領,提升企業核心競爭力 堅持高質量發展策略,塑強核心競爭優勢...

關鍵字: 通信 BSP 電信運營商 數字經濟

北京2024年8月27日 /美通社/ -- 8月21日,由中央廣播電視總臺與中國電影電視技術學會聯合牽頭組建的NVI技術創新聯盟在BIRTV2024超高清全產業鏈發展研討會上宣布正式成立。 活動現場 NVI技術創新聯...

關鍵字: VI 傳輸協議 音頻 BSP

北京2024年8月27日 /美通社/ -- 在8月23日舉辦的2024年長三角生態綠色一體化發展示范區聯合招商會上,軟通動力信息技術(集團)股份有限公司(以下簡稱"軟通動力")與長三角投資(上海)有限...

關鍵字: BSP 信息技術
關閉
關閉