Stm32f103 DAC 最低電流輸出問題

最近在做電流型信號輸出的項目，遇到了些問題這里把這些解決方法做一個筆記方便以后運用。在搞這個的時候因?yàn)槭謨?cè)這部分講的不是很詳細，所以在使用上也遇到了些阻力。

用的是64封裝的芯， 此芯ADC的基準Vref+和電源是同一個端口，Vref-共用電源地。在電池輸出時AD值為0時 取樣電阻100歐姆有0.66mA的電流輸出，只要在初始化時只要失能端口輸出緩沖，輸出可到0.0025mA。OK問題就解決了。

1 void AnalogInit(void)

2 {

3 DAC_InitTypeDef DAC_InitStructure;

4 GPIO_InitTypeDef GPIO_InitStructure;

5

6 RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO | RCC_APB2Periph_GPIOA, ENABLE);

7 /* DAC Periph clock enable */

8 RCC_APB1PeriphClockCmd(RCC_APB1Periph_DAC, ENABLE);

9

10 /* Configure DAC channe1 output pin */

11 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4;

12 GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

13 GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;

14 GPIO_Init(GPIOA, &GPIO_InitStructure);

15

16 /* Configure DAC channe1 output pin */

17 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;

18 GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

19 GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;

20 GPIO_Init(GPIOA, &GPIO_InitStructure);

21

22

23 /* DAC channel1 Configuration */

24 DAC_InitStructure.DAC_Trigger = DAC_Trigger_Software;

25 DAC_InitStructure.DAC_WaveGeneration = DAC_WaveGeneration_None;

26 DAC_InitStructure.DAC_OutputBuffer = DAC_OutputBuffer_Disable; //輸出緩沖失能

27 DAC_InitStructure.DAC_LFSRUnmask_TriangleAmplitude = DAC_TriangleAmplitude_4095;

28

29 DAC_Init(DAC_Channel_1, &DAC_InitStructure);

30

31 /* DAC channel2 Configuration */

32 DAC_Init(DAC_Channel_2, &DAC_InitStructure);

33

34 /* Enable DAC Channel1: Once the DAC channel1 is enabled, PA.04 is

35 automatically connected to the DAC converter. */

36 DAC_Cmd(DAC_Channel_1, ENABLE);

37 /* Enable DAC Channel2: Once the DAC channel2 is enabled, PA.05 is

38 automatically connected to the DAC converter. */

39 DAC_Cmd(DAC_Channel_2, ENABLE);

40

41 }

42

43 //端口1AD值更新

44 void DAC1_update(u16 ch1)

45 {

46 ch1 = (ch1 <<4) & 0xfff0;

47 /* Set DAC Channel1 DHR12L register */

48 DAC_SetChannel1Data(DAC_Align_12b_L, ch1);

49

50 /* Start DAC Channel1 conversion by software */

51 DAC_SoftwareTriggerCmd(DAC_Channel_1, ENABLE);

52 }

53

54 void DAC2_update(u16 ch2)

55 {

56 ch2 = (ch2 <<4) & 0xfff0;

57 /* Set DAC Channel2 DHR12L register */

58 DAC_SetChannel2Data(DAC_Align_12b_L, ch2);

59

60 /* Start DAC Channel1 conversion by software */

61 DAC_SoftwareTriggerCmd(DAC_Channel_2, ENABLE);

62 }