LPC1788--SSP設置驅動W25Q16--以及特別注意點

在學習過程中，發現一點容易被忽視而又很?chē)?yán)重的問題---那就是關于SSP1的引腳使用P0[7]-P0[8]-P0[9]時，是W型IO配置。寄存器的第7位很容易被我們?cè)O(shè)置為0--但是手冊上是要求必須為1，否則不能正常工作，這里我走了一點彎路。

#include"ssp_lpc1788.h"

#define SPI_FLASH_PageSize 256 //頁大小
#define SPI_FLASH_PerWritePageSize 256 //寫頁大小

/*----------------初始化SSP0-------------*/
void SSP0_Init(unsigned long sysClk, unsigned spiClk)
{
volatile uint32_t dummy;

dummy = dummy;

LPC_IOCON->P2_22 =0x22; // SSP0_SCK
LPC_IOCON->P2_26 =0x22; // SSP0_MISO
LPC_IOCON->P2_27 =0x22; // SSP0_MOSI

LPC_IOCON->P2_23=0x30; //SSP1_CS-直接普通上拉IO
LPC_GPIO2->DIR "= (1UL << 23); //輸出
LPC_GPIO2->SET|=(1<<23);//置一

LPC_SC->PCONP |= (1UL << 21); //SSP0 時鐘開啟

LPC_SSP0->CR0 = 0x0007; // 8Bit, CPOL=0, CPHA=0
LPC_SSP0->CR1 = 0x0002; // SSP0-使能-主模式

LPC_SSP0->CPSR = sysClk/spiClk; //時鐘預分頻寄存器

while( LPC_SSP0->SR & ( 1 << 4 ) ); //忙

while( LPC_SSP0->SR & ( 1 << 2 ) ) //接收FIFO不為空
{
dummy = LPC_SSP0->DR; //假讀取去清空FIFO
}

}

/*-------------SSP0-發送數據-----------------*/
void SSP0_WriteByte(unsigned char data)
{
uint8_t Dummy;

LPC_SSP0->DR = data; //載入要發送的數據
while (LPC_SSP0->SR & (1 << 4)){}//等待發送完成
Dummy=LPC_SSP0->DR; //假讀取去清空FIFO
}

/*-------------SSP0-接收數據-----------------*/
uint8_t SSP0_RegisterByte(void)
{
LPC_SSP0->DR = 0xFF; //無效指令
while (LPC_SSP0->SR & (1 << 4)){}//忙等待

return (LPC_SSP0->DR); //接收數據
}

/*-----------------------------------SSP1--------------------------*/
/*----------------初始化SSP1-------------*/
void SSP1_Init(unsigned long sysClk, unsigned spiClk)
{
volatile uint32_t dummy;

LPC_IOCON->P0_7 =0xA2; // SSP1_SCK
LPC_IOCON->P0_8 =0xA2; // SSP1_MISO
LPC_IOCON->P0_9 =0xA2; // SSP1_MOSI

LPC_IOCON->P0_6=0x30; //SSP1_CS-普通上拉IO
LPC_GPIO0->DIR |= (1UL << 6); //輸出
LPC_GPIO0->SET|=(1<<6);//置一

LPC_SC->PCONP |= (1UL << 10); //SSP1 時鐘開啟

LPC_SSP1->CR0 = 0x0007; // 8Bit, CPOL=0, CPHA=0
LPC_SSP1->CR1 = 0x0002; // SSP1-使能-主模式

LPC_SSP1->CPSR = sysClk/spiClk; //時鐘預分頻寄存器

while( LPC_SSP1->SR & ( 1 << 4 ) ); //忙

while( LPC_SSP1->SR & ( 1 << 2 ) ) //接收FIFO不為空
{
dummy = LPC_SSP1->DR; //假讀取去清空FIFO
}
}

/*-------------SSP1-發送數據-----------------*/
void SSP1_WriteByte(unsigned char data)
{
uint8_t Dummy;

LPC_SSP1->DR = data; //載入要發送的數據
while (LPC_SSP1->SR & (1 << 4)){} //等待發送完成
Dummy=LPC_SSP1->DR; //假讀取去清空FIFO
}

/*-------------SSP1-接收數據-----------------*/
uint8_t SSP1_RegisterByte(void)
{
LPC_SSP1->DR = 0xFF; //無效指令
while (LPC_SSP1->SR & (1 << 4)){} //忙等待

return (LPC_SSP1->DR); //接收數據
}

/*---------------------W25Q16---------------*/
//---------寫使能---
void SSP_FLASH_WriteEnable(void)
{
FLASH_CS_LOW();
SSP0_WriteByte(0x06);
FLASH_CS_HIGH();
}
//--------等待寫完成--
void SSP_FLASH_WaitForWriteEnd(void)
{
uint16_t i=2000;
uint8_t FLASH_Status = 0;

FLASH_CS_LOW();
SSP0_WriteByte(0x05);
do
{
FLASH_Status = SSP0_RegisterByte();
i--;
}
while (((FLASH_Status & 0x01) == 1)||(i==0));
FLASH_CS_HIGH();

}

/*----關于擦除---在寫入數據之前必須保證被寫入的位值是0xff---這就是擦除的作用*/

//-------------扇區擦除----------
void SSP_FLASH_SectorErase(uint32_t SectorAddr)
{
SSP_FLASH_WriteEnable();//寫使能
SSP_FLASH_WaitForWriteEnd();//忙狀態

FLASH_CS_LOW();//CS=0
SSP0_WriteByte(0x20);//0x20
SSP0_WriteByte((SectorAddr & 0xFF0000) >> 16);//擦除扇區起始地址
SSP0_WriteByte((SectorAddr & 0xFF00) >> 8);
SSP0_WriteByte(SectorAddr & 0xFF);
FLASH_CS_HIGH();//CS=1

SSP_FLASH_WaitForWriteEnd();//忙狀態--等待擦除完成
}
//-----------塊擦除-------
void SSP_FLASH_BlockErase(uint32_t BlockAddr)
{
BlockAddr*=65536;//0x010000
SSP_FLASH_WriteEnable();//寫使能
SSP_FLASH_WaitForWriteEnd();

FLASH_CS_LOW();
SSP0_WriteByte(0xD8);//0xD8
SSP0_WriteByte((BlockAddr & 0xFF0000) >> 16);//擦除塊起始地址
SSP0_WriteByte((BlockAddr & 0xFF00) >> 8);
SSP0_WriteByte(BlockAddr & 0xFF);
FLASH_CS_HIGH();

SSP_FLASH_WaitForWriteEnd();
}
//----------整片擦除--
void SSP_FLASH_BulkErase(void)
{
SSP_FLASH_WriteEnable(); //寫使能

FLASH_CS_LOW();
SSP0_WriteByte(0xc7); //整片擦除
FLASH_CS_HIGH();

SSP_FLASH_WaitForWriteEnd();
}
//---------單頁寫入-----
void SSP_FLASH_PageWrite(uint8_t* pBuffer, uint32_t WriteAddr, uint16_t NumByteToWrite)
{
SSP_FLASH_WriteEnable();

FLASH_CS_LOW();
SSP0_WriteByte(0x02);//CMD2--0x02--------頁寫入
SSP0_WriteByte((WriteAddr & 0xFF0000) >> 16);//寫入起始地址
SSP0_WriteByte((WriteAddr & 0xFF00) >> 8);
SSP0_WriteByte(WriteAddr & 0xFF);

if(NumByteToWrite > SSP_FLASH_PerWritePageSize) //寫入數據多余頁最大數據
NumByteToWrite = SSP_FLASH_PerWritePageSize;
while (NumByteToWrite--)
{
SSP0_WriteByte(*pBuffer); //寫數據
pBuffer++;
}
FLASH_CS_HIGH();

SSP_FLASH_WaitForWriteEnd();
}
//--------多頁寫入---
void SSP_FLASH_BufferWrite(uint8_t* pBuffer, uint32_t WriteAddr, uint16_t NumByteToWrite)
{
uint8_t NumOfPage = 0, NumOfSingle = 0, Addr = 0, count = 0, temp = 0;

Addr = WriteAddr % SSP_FLASH_PageSize; //首頁地址
count = SSP_FLASH_PageSize - Addr;//首頁要寫入的數據個數
NumOfPage = NumByteToWrite / SSP_FLASH_PageSize;//頁數
NumOfSingle = NumByteToWrite % SSP_FLASH_PageSize; //余數--最后一頁不滿一頁個數

if (Addr == 0)
{
if (NumOfPage == 0) //只有一頁
{
SSP_FLASH_PageWrite(pBuffer, WriteAddr, NumByteToWrite); //?±?óD′è?
}
else //多頁
{
while (NumOfPage--) //寫滿頁的數據
{
SSP_FLASH_PageWrite(pBuffer, WriteAddr, SSP_FLASH_PageSize);
WriteAddr += SSP_FLASH_PageSize;
pBuffer += SSP_FLASH_PageSize;
}

SSP_FLASH_PageWrite(pBuffer, WriteAddr, NumOfSingle);//寫最后不滿一頁的數據
}
}
else
{
if (NumOfPage == 0)
{
if (NumOfSingle > count)
{
temp = NumOfSingle - count;
SSP_FLASH_PageWrite(pBuffer, WriteAddr, count);
WriteAddr += count;
pBuffer += count;

SSP_FLASH_PageWrite(pBuffer, WriteAddr, temp);
}
else
{
SSP_FLASH_PageWrite(pBuffer, WriteAddr, NumByteToWrite);
}
}
else
{
NumByteToWrite -= count;
NumOfPage = NumByteToWrite / SSP_FLASH_PageSize;
NumOfSingle = NumByteToWrite % SSP_FLASH_PageSize;

SSP_FLASH_PageWrite(pBuffer, WriteAddr, count);
WriteAddr += count;
pBuffer += count;

while (NumOfPage--)
{
SSP_FLASH_PageWrite(pBuffer, WriteAddr, SSP_FLASH_PageSize);
WriteAddr += SSP_FLASH_PageSize;
pBuffer += SSP_FLASH_PageSize;
}

if (NumOfSingle != 0)
{
SSP_FLASH_PageWrite(pBuffer, WriteAddr, NumOfSingle);
}
}
}
}
//--------讀數據-----------
void SSP_FLASH_BufferRead(uint8_t* pBuffer, uint32_t ReadAddr, uint16_t NumByteToRead)
{
FLASH_CS_LOW();
SSP0_WriteByte(0x03); //CMD3--0x03-----//讀數據
SSP0_WriteByte((ReadAddr & 0xFF0000) >> 16);
SSP0_WriteByte((ReadAddr& 0xFF00) >> 8);
SSP0_WriteByte(ReadAddr & 0xFF);

while (NumByteToRead--)
{
*pBuffer = SSP0_RegisterByte();//讀入到指定數組
pBuffer++;
}
FLASH_CS_HIGH();
}

/*-----------讀取廠家ID------------*/
uint32_t SSP_FLASH_ReadID(void)
{
uint32_t temp1=0,temp2=0,temp3=0,temp=0;

LPC_GPIO0->CLR|=(1<<6); //CS=0

SSP1_WriteByte(0x9F); //讀取ID指令
temp1 =SSP1_RegisterByte(); //廠家編號
temp2 =SSP1_RegisterByte();//存儲類型
temp3 =SSP1_RegisterByte();//容量

temp =(temp1<<16)|(temp2<<8)|(temp3);

LPC_GPIO0->SET|=(1<<6);//CS=1;

return temp;