STM32使用Flash存儲器當作EEPROM來保持?jǐn)?shù)據

嵌入式應用中經常會遇到需要保存一些數據比如選項和設置等等，為了在設備關機或掉電情況下數據不丟失，我們會講數據保存在EEPROM里面。STM32系列MCU已經被廣泛的使用，可是該芯片內沒有EEPROM。如果外接一片EEPRM會增加硬件成本。

本文將以STM32F0為例介紹一種使用片內Flash替代EEPROM的方法，僅供大家參考。

STM32F0芯片內部Flash頁尺寸為1k。

首先程序需要使用STMicroelectronics提供的標準外設庫中的stm32f0xx_flash.h。如下：

#include "stm32f0xx_flash.h"

//定義常量 (以STM32F051R8為例)
#define FLASH_PAGE_SIZE((uint32_t)0x00000400)
#define FLASH_USER_START_ADDR((uint32_t)0x0800FC00)
#define FLASH_USER_END_ADDR((uint32_t)0x08010000)

//定義需保存數據的結構
typedef struct
{
uint8_t sensitivity;
uint8_t track_no;
uint8_t high_lumi;
uint8_t low_lumi;
uint32_t hold_time;
uint8_t adc_output;
uint8_t dim_step;
uint16_t reserved;
uint32_t data_valid;
} _settings;

//為了方便變量的使用和在Flash里面的存貯，定義一聯合
typedef union
{
uint32_t DataAll[4];//因?yàn)樽兞拷Y(jié)構總共為16 bytes，所以為4個32位變量
_settings DataI;
} settings;

//申明變量，注意一定要四字節對齊
A_ALIGNED volatile settings sensor_set;

//各功能函數
void UserErase(void)
{
FLASH_ErasePage(FLASH_USER_START_ADDR);
}

void UserRead(void)
{
int i;
uint32_t address_t;

address_t = FLASH_USER_START_ADDR;

for(i=0;i
{
sensor_set.DataAll[i] = *(__IO uint32_t *)address_t;
address_t += 4;
}
}

void UserWrite(void)
{
int i;
uint32_t address_t;

//Unlock the Flash to enable the flash control register access
FLASH_Unlock();

// Erase the FLASH pages
UserErase();//FLASH_ErasePage(FLASH_USER_START_ADDR);

// Program the user Flash area word by word
address_t = FLASH_USER_START_ADDR;

for(i=0;i
{
FLASH_ProgramWord(address_t, sensor_set.DataAll[i]);
address_t += 4;
}

// Lock the Flash to disable the flash control register access (recommended
//to protect the FLASH memory against possible unwanted operation)
FLASH_Lock();
}

//變量的使用

//在main（）函數做初始化時讀取設置參數
UserRead();

//使用設置參數
if(sensor_set.DataI.sensitivity == 1)
{
//
}

//根據需要改變設置參數為3
sensor_set.DataI.sensitivity = 3;
UserWrite();//記住任何一個設置改變了都需要保存到Flash里面。